Experience the Royal Treatment Today
Licensed & Insured. NYC Lic. #2030146

Re-roofing is the quickest and least expensive route to renew your roof’s appearance. During roofing, a makeshift shingle overlay is deposited over your worn shingles to renew the look of your roof as well as give a defensive layer to help preclude leaks from getting inside your home. The foremost step is to contact a professional roofing contractor, they will set up an appointment with you to tread the roof and perform a roof survey. Once they complete the examination, they will give you possible results grounded on the damage they found on the roof.

Ways To Reroof A Flat Roof

Maybe you’re a fan of single-bias roofing systems, so you’re going to stick with that. And there have been refinements in single-bias since your last installation. No matter which roof system you presently have, you’ll always be suitable to take off it and install a new one.

Let’s say you did have that single-bias roof with a few leaks.  After an examination, it’s determined that 15 of the roof’s sequestration is saturated. A cost-effective option that some structure possessors don’t know about is roof coating restoration. This is done by installing high-quality, leakproof silicone over an existing roof. To repair a roof and it’s an EPDM rubber roof, a roofing contractor would identify where all the wet sequestration is and take off only those areas. They will replace the wet sequestration with new, dry sequestration and EPDM. Now they will prep the existing roof by power bathing the roof clean. They will also perform bonding tests to make sure the coating will stick rightly. Next, they will treat the seams since these regions are apt to leaking. Also, they will apply a certain viscosity of the coating to the entire roof.

If your flat roof is leaking, there isn’t a befitting slope to transport water to drains, there are openings in the membrane, and flashings around penetrations are not watertight. However, an option to reckon with is a spray foam roof, if any of these effects are happening to your flat roof. Because spray foam can rule out all three of the issues above. Spray froth can impact the proper slope and it fills in holes in the membrane. Over time, flashings begin to fragment down, lose adhesion, or turn cracked, which gives water an entry point into the sequestration. With foam being spray-applied, a contractor can spray over the top of the subsisting flashings and make it a part of the one-layer roofing system.

To confirm if your flat roof needs a repair or replacement, get in touch with a professional roofer or roofing company to do a thorough inspection of the building.

To get the best roofing job done, always contact a professional roofing company like us at 70 Sunrise Highway #500 Valley Stream, New York 11581 (516)- 252-3001 https://www.gafroofinglongisland.com/

While a well-installed, duly preserved, a flat roof can last for numerous years, like all roofs, they face the weight of our haphazard weather patterns. Flat roofs are adept for a mass of reasons, but it’s important to know and be competent to recognize some of the most everyday issues and contact an experienced roofer to fix it. Below are some of their issues and how to go about it.

  1. Standing Water

When water is left to stand for ages of time on your roof, it can bring about damage to the shell material of your roof and the fresh weight of the water can beget troubles for the structure of the roof itself. However, water leaks into the roof space or through to the occupied place below are unavoidable, if left for too long. Once the roof exterior has been accessed by water, problems like spoilage, mould, and fungus can oppressively hazard the roof structure. Discerning a water leak inside your home or commercial structure is frequently a sign that standing water has been left too long unnoticed. Regular examinations of your roof will wake you to any areas of ponding as soon as they materialize. You can try to rectify the reason for the problem before it comes to be a prominent issue.

  1. Surface debilitation

This is a big problem that encompasses cracks, blistering, rips, or any distinct observable signs of detriment to the surface of your flat roof. Damage to the surface of your flat roof is an effortless one to spot during a roof examination. As a general rule, it's anticipated that your roof surface form will regress over time as a regular part of aging.

  1. Ineffective Drainage

Stuffed drains, inadequate drainage allowances, and lousy workmanship can lead to water detriment on your flat roof. Roof plumbing is what we call everything to do with getting water off your roof and into the gutters and it's a dynamic aspect of your roof’s blueprint and function. Keep your roof and gutters free of debris. Regularly examining your roof can alleviate any ongoing problems.

  1. Impoverished installation

Unfortunately, poor workmanship on the installation of your flat roof can result in numerous of the issues we've formerly talked about. The lifetime of a flat roof can be anywhere from 20 to 50 years, hinging on the roof material you choose and the site specifics. However, it’s likely to be a problem due to skint quality workmanship, If you're noticing problems with your flat roof far earlier in its lifespan than you anticipated. Employing educated flat roof installers to fit your new roof will help cover your home or commercial structure against some of the most everyday problems faced with flat roofs.

Our professional crew has a proven history of happy guests and successful systems. Expert finishing will mean you don’t have to worry about standing water, leaks, surface detriment, or improper fittings.

Reach out to us today at 70 Sunrise Highway 500 Valley Stream, New York 11581 516-252-3001 https://www.gafroofinglongisland.com/ for examinations and fixing of your roof problems.

You may be wondering if you have tempest damage that requires your attention, if it's indeed worth filing a claim. It's important to check your roof and environing property for damage right off, as insurance procedures generally include an enactment of limitations time frame with a deadline for how long after a circumstance you can file a claim. Also, if you have hail or other active damage to your roof, you might retain a roof leak that can create hidden interior damage or mold. Not all homeowners or property possessors’ insurance policies give the quantum of coverage you need after a disaster.

It's important to know the type of policy content you have, as this can affect how much out-of-fund expenditure you may incur. Your policy likely includes a deductible that you're needed to pay toward the cost of an insurance claim before insurance coverage kicks in. Policies pay different quantities to fix or replace property damage coinciding to the type of wind/hail coverage you bought with your policy. After the deductible is paid, the quantum you get for your claim depends on whether your course includes ACV or RCV coverage.

Actual cash value coverage means that your insurance company agrees to compensate you for the value of your roof in its prevailing state. Basically, diminishment is factored into your claim agreement. diminishment is calculated by a claims adjuster, who'll check the roof to determine its replacement expenditure, review its current condition and estimate its remaining lifetime. ACV is calculated as the quantum needed to replace or fix your roof minus any misplacement in value associated with the age of your roof. There's a connection between the age of your roof and your insurance content. ACV coverage is generally used for aged roofs or roofs that are in poor condition.

Replacement cash coverage is a bit simpler to deduce than actual cash value. However, the insurance company is agreeing to compensate you what it would cost to substitute your roof with alike new roof, if you have a homeowners policy that covers your roof on a replacement cost base. Your claims adjuster will probe new roofing accoutrements that are similar to what you have on your home now and offer you an agreement grounded on what it would cost to replace your roof with a resembling new roof.

Your claims adjuster will ground their assessment on new roofing accoutrements that are similar to what you presently have and offer you a settlement for what it would cost to replace your roof with these accoutrements. Replacement cost coverage commonly costs more than actual cash value content, but it generally means that your deductible could be your only out-of-fund expenditure if your roof is damaged.

It's important to be familiar with the insurance delivered by your policy. If you're troubled about storm damage or think you may have a roof leak, contact us at Royal Roofing & Siding, 70 Sunrise Highway #500 Valley Stream, New York 11581 https://www.gafroofinglongisland.com right away.

Roof bags for cars increase the cargo capacities of vehicles, allowing motorists to carry further items on road trips, out-of-door adventures, and other occasions. These bags come in a variety of shapes, sizes, and outfit to suit different vehicles and purposes. With so numerous options available, you may have a tough time deciding which unique roof bag is accurate for you.

Importance Of Roof Bags For Cars

Roof bags for cars are gear storehouse bags meant to be affixed to the top of a vehicle. They are useful for motorists who need to carry a lot of load and passengers. By allowing you to place a load on top of your car, a roof bag can free up a passenger or a load space in your vehicle.

The numerous reasons why you may want to buy a roof bag for your vehicle, includes;

1.Spare storage: If you have a small vehicle, you may run out of storage space when you take your whole family on a long road trip. While you cannot increase the load area or box space in your vehicle, you can create further storage room by using a rooftop bag.

2.Upgraded passenger comfort: Spending hours in a vehicle can be discomforting, specifically for passengers who have to sit next to a bunch of unsecured luggage. Fortunately, you can unriddle this problem by getting a rooftop bag for your car. This creates excess space for your passengers, permitting them to stretch out and enjoy the journey.

3.Protection against the rudiments: High-quality rooftop bags for cars are made of durable, leakproof accoutrements. thus, you do not have to worry about your haul being damaged due to exposure to the rudiments.

4.Flexible storage: Since they are made of flexible accoutrements, rooftop bags are ideal for storing oddly shaped items such as sports outfit and musical instruments.

5.Increased security: If you are driving an SUV or station wagon, putting too much stuff in the rear can be dangerous as it may obstruct your rear visibility. By using a rooftop bag, you can reduce the quantum of weight in the rear and enhance your rear vision always.

Types Of Roof Bags For Cars

Primarily, there are only two types of rooftop bags, which are:

These rooftop bags come with strips and buckles that permit them to be tied to the roof racks of a car. They generally cannot be used on vehicles that do not have roof racks.

Rooftop bags for vehicles without roof racks have hooks that go under the weather-strips in auto doors. generally, these bags can also work with roof racks, making them a more adjustable option.


Good roof bags for cars are generally more expensive. Notwithstanding, they are worth the excess cost because they give better protection for your things and last longer. For the best quality roof bags contact us at 70 Sunrise Highway #500 Valley Stream, New York 11581 (516)- 252-3001 https://www.gafroofinglongisland.com/.

Certain rooftop tile materials can be painted yet at the same, but not all. Concrete, record, and earth tiles can be in every way painted. Earthenware rooftop tiles, nonetheless, can't be painted. In a situation where you're hoping to invigorate the presence of your rooftop, painting it could be the most ideal choice. Painting your rooftop tiles isn't a necessity. This is a corrective decision that affects toughness.

Whenever you've decided you need your substantial rooftop tiles painted, try to choose top-quality 100 percent acrylic paint. Acrylic paints are practical, simple to introduce (using a shower or roller), and have high protection from UV beams. Setting up the surface is fundamental to setting up your rooftop before painting. Have professional roofers to fix, clean, and prime your rooftop tiles before you get them painted. You'll likewise need to ensure every one of the breaks, holes, spills, and other rooftop issues are fixed before you start painting.

Is It Okay To Paint Rooftop Tiles?

For material tiles, water-based paints, particularly implied for rooftops are your smartest option. Be that as it may, painting material tiles is undeniably more hazardous and include the utilization of framework, stream washing, fungicidal wash lastly an airless sprayer to paint them, so it is best passed on to the experts.

What Paint Can You Use On Roof Tiles?

Acrylic Roof and Tile Paint

Acrylic paint gives a great waterproofing arrangement and is best reasonable in waterproofing paint for rooftop and waterproofing paint for porch, worked with rectangular blocks.

GAF Roofing acrylic rooftop and tile paint is an effectively relevant, water-based item. In light of 100 percent unadulterated acrylic, this paint offers harm strength, enduring adaptability, and waterproofing. Letting out water and dampness for long-haul security against weather conditions damage is planned. Accessible in a scope of varieties, this paint is great for any remodel project, or to safeguard rooftop tiles from serious harm.

How Long Does Rooftop Paint Last?

At the point when you utilize the right great paint for the work joined with acknowledged application strategies on top of satisfactory surface readiness you can expect rooftop paint to keep going for a very long time and that's just the beginning. On the off chance that you disregard the surface planning your paint execution won't ever keep going as long regardless of how great the paint is.

Your rooftop ought to be painted each 10-15 years, or at whatever point the rooftop covering breaks down. For what reason do I have to paint my rooftop? The purpose for painting your rooftop each 10-15 years is because once the covering (rooftop layer) brakes down and the tile is left exposed, the substantial will start to gradually separate over time.

GAF Roofing is here to offer you top-notch painting for your home’s roof. Get to us at 70 Sunrise Highway #500 Valley Stream, New York 11581 (516)- 252-3001  https://www.gafroofinglongisland.com/.

Whether you're developing another form or equipping to handle buildup in your own home, satisfactory rooftop ventilation is an unquestionable necessity. There are a couple of interesting points before you start introducing rooftop vents. First and foremost, you want to decide the number of rooftops vents you want, what sort of vents are best for your property, and in particular how to accurately introduce them.

The services of a great roofer or roofing agency will help you achieve that. Meanwhile, let us look at how you can install a GAF roof vent by yourself.

Step-by-Step Instructions To Install A Roof GAF Roof Vent

A few property holders would prefer to add rooftop vents to their current rooftop themselves, and if you're one of them, read through our bit-by-bit guide before you get everything rolling. To begin with, this is the very thing that you'll require:

Then, utilize this 10-step interaction to figure out how to add ventilation to your rooftop:

  1. Go up to your loft and choose where you need to introduce your rooftop vent(s). Mark the area by boring an opening vertical through the center of the area you've picked and leave the bore standing up, so you can track down it from an external perspective.
  2. Position the stepping stool, and move up onto your rooftop. Ensure you're utilizing appropriate wellbeing insurances.
  3. Find the drill bit(s) on the rooftop.
  4. Utilize your ruler to gauge the open region of the vent. Then, utilizing the bore as the middle, measure a similar size space onto your rooftop with the ruler and a checking pencil.
  5. Utilize your saw (a jigsaw or responding saw for best outcomes) to slice along the deliberate lines through both the shingles and the wood under them.
  6. Release the shingles around the opening utilizing your pry bar.
  7. Turn the vent potential gain and apply caulk to the spine.
  8. Allowing the base side of your vent to be uncovered and laying over the shingles, slide the sides and top of the vent under the shingles that are encompassing it.
  9. Secure the vent to your material design by pounding in a nail each couple of inches.
  10. Use nails to get some other shingles in the space that are free.

Assuming you have any inquiries concerning this cycle, go ahead and get in touch with GAF Roofing. We are ready to assist you no matter what. It will surprise you that the cost of installing a roof vent is average and very affordable. Just in case you do not want to go through the hassle of fixing it on your own, get in touch with a professional roofing agent like the GAF Roofing in Long Island.

We offer great estimates and our services are top-notch, contact us at 70 Sunrise Highway #500 Valley Stream, New York 11581 (516)- 252-3001  https://www.gafroofinglongisland.com/.

Flat roof ventilation is necessary for flat roofs in any home building. This is also essential for cold flat roofs. GAF roof ventilation is here to offer you awesome roof ventilation services for your home’s roof. Roof ventilation is important for the easy flow of air in and out of the attic area of the house, especially humid or hot air. This brings a comfortable atmosphere to the home and for the residents.

GAF flat room ventilation is achieved when the same amounts of air intake and air exhaust are gotten. Possessing both of these will aid easy breath of the cavity along with the cross ventilation. To make ventilation for a flat roof, circulating the sir in the plenum or attic is what is required. As attic ventilation is vital and can aid in sustaining the building’s health or strength.

GAF roof vents come in many types of clean-cut lengths. This is to ensure good ventilation of air. In as much as flat roof vents are popular for poor drainage, GAF roof vents are packaged in a good number of heights, very high to avoid any form of leakage. Roof curbs and vents along curb mount flanges come with it to give more protection and guard for the flat roof vents.

Some basic outstanding features are:

3 Types Of GAF Flat Roof Vents.

  1. Breather Vent: This vent permits moisture to come out as it releases any moisture trying to enter. This is a major problem with attic spaces; holding a large amount of condensation and the breather vent helps to reduce that. They function together as a billow that opens and closes by the moisture content around the attic area.
  2. Aura Vent: The aura ventilator is the best choice for a low-profile type of flat roof. It comes with a rounded head that rotates to allow the hot or humid air to come out of the attic. This happens while fresh and cooler air comes in at the same time. It possesses a classy design.
  3. Boot Vent: This type can be used on residential homes that have flat roofs. The boot vent system is standard that easily acts as a holder as well as a base for pipping which comes via the roof.

These are only a few of the best among the various types of GAF flat roof vents available.

Do you have a residential home that has a flat roof? Are you a home builder who wishes to have a flat roof for your home? The GAF flat roof vents are available and it is the best flat roof vents popular in New York. The flat roof vents come at cheat-taking prices.

For your flat roof vents, contact us at 70 Sunrise Highway #500 Valley Stream, New York 11581 (516)- 252-3001 https://www.gafroofinglongisland.com/.

A lot of homeowners have been asking "is GAF Shingles better than Owen Corning ". There has been so much difficulty picking between these two leading brands. Each brand has its unique advantages and disadvantages. To help you make a well-informed decision, it’ll be best to contact an expert roofing company to enquire more about the best roofing brand.

In this article, we'll break down the significant differences to determine which one is perfect for your home.

GAF Shingles: Advantages And Disadvantages

Here are some of the major advantages and disadvantages of the GAF Shingles.


GAF Shingles come in diverse colors which homeowners can choose for their roofs. This availability of color options is quite appealing as not all roof brands have black options

These shingles are designed with natural wood grain which gives them a blended natural look similar to that of real wood.

The GAF Timberline Shingles are equipped with Duraweave Fiberglass Reinforcement Technology and are over 30% strong against wear and tear. This feature makes it more unique.


Even though the GAF Shingles are not as costly as other brands, they are more expensive than Owens Corning.

These shingles aren't simple DIY products. You'll need to hire the services of an expert install which will end up costing more money.

Owens Corning: Advantages And Disadvantages

These are the unique advantages and disadvantages of Owens Corning that set it apart from other brands.


You won't spend so much money if you settle for the Owen Corning. Plus, there's felt paper (or water shield) installed over an asphalt-shingle underlayment or plywood deck to reduce the money that would have been spent on installation.

They are highly durable. Also, they have EverGuard Technology built in to make them 50% stronger (against wear and tear) than other roofing material brands.

These products have a warranty of between 40 to 50 years.


These shingles aren't built equally as some batches have lower quality than others. To avoid this kind of problem, maybe buy from a contractor with high-quality Owens Corning manufactured shingles.

The color palette options on Owens Corning are barely enough. Unfortunately, homeowners are now setting it aside and settling for lighter roofs.

Is GAF Shingles Better Than Owens Corning?

There’s no doubt that these two are industry-leading brands. In terms of warranty (wind), the GAF Shingles are better than Owens Corning. GAF provides a non-prorated wind warranty of 130+ MPH for premium and architectural shingles while Owens Corning offers just 110+ MPH.

When it comes to energy efficiency, the brands are on the same platter. In all, what matters most is your budget and style preference. The Owens Corning is less expensive than the GAF Shingles, and you may want to settle for that if you're working within a budget. The Owens Corning Duration Cool is a perfect pick.

Bottom Line

In sum, we submit that Owens Corning is the better option for many reasons. They are readily available and affordable. At Long Island Roofing Services, we offer expert roofing services at the best price. Contact us today for a FREE estimate!

You can visit us at 70 Sunrise Highway #500 Valley Stream, New York 11581, or call us at (516)- 252-300 https://www.gafroofinglongisland.com/.

The best roof vents don't just make your roof last longer. They help reduce your home's energy bills and make your house a healthier place to live. Therefore, you have to seek the advice of an expert roofer to get the best recommendations for a roof vent for your home. We've compiled a list of the best roof vents for your long island home. Let's dive in.

Which Type Of Roof Vent Is Best For My Home?

Generally, the most recommended is a ridge vent for exhaust and a soffit vent for intake. However, for a long island home that can't use ridge vents, box vents are the next best option for exhaust. In comparison, fascia vents can replace soffit vents. Your roof's vent varies depending on the shape of your roof and your home's style. Also, vertical ventilation is more effective than cross or horizontal ventilation.

Types Of Roof Vent

The different roof vent types are effective in their way.  Each of them has the primary task of either bringing fresh air into the home or removing stale air from your attic space.

If you want to benefit from proper ventilation, it'll be best to install both exhaust and intake ventilation. However, the design of some roofs supports just one. Some roof vents are:

Ridge Vents

These vents are mostly used as exhaust vents. They are installed across the peak of the roof and run across the whole span of your roofline. They are in a prime position to allow the hottest air to leave the attic space and have enough surface area to expel large amounts of hot air. They function perfectly in vertical ventilation.

Box Vents

This vent is otherwise called a louver vent. These vents are used for exhaust ventilation. They are akin to off-ridge vents in the installation process, as you'll have to cut a hole in the roof for the vent to sit over.

Box vents are installed in groups across the roof to add extra ventilation. So, using one or two box vents isn't enough for the entire roof. The most commonly used box vent is 18 x 18 inches. However, they are versatile and can be installed in smaller areas that require air ventilation, even though they have a small size.

Attic Power Vents

These vents, otherwise called powered attic ventilators, are fans propelled by electricity that help pull out the stale air from the attic space but at a high cost. They function as box fans placed in the window on a hot summer day.

This vent keeps the attic at a constant temperature, preventing extreme fluctuations in temperature from season to season. However, their power may not be powerful enough for the ventilation strategy, or they may be detrimental.

Gable Vents

These vents are mostly triangular made of metal, vinyl, or wood; and function as an exhaust system, but they are outdated. They use cross or horizontal ventilation to keep the air around the attic space. This vent is mostly used with a gable-style roof since it can be placed on each side of the home.

Unfortunately, these vents aren't effective on complex roof styles because peals, dormers, valleys, and other roof parts can hinder the cross breeze.

Fascia Vents

This vent type is majorly for roofs that don't have sufficiently sized eaves that fit the soffit vents. This vent is placed on top of the fascia board, directly underneath the starter row of shingles. Fascia vents allow the intake of air where the wind hits the roof, as opposed to a soffit vent that allows air to rise.


When looking for the best roof vent for your long island home, reach out to a professional roofing specialist before deciding. It's always necessary to get quotes from an experienced roofing contractor. If you need a new roof and would like to discuss which venting strategy is best for your home, we're here to help. Reach out to us at 70 Sunrise Highway, #500 Valley Stream, New York 11581 (516) - 252 – 3001 https://www.gafroofinglongisland.com/.

Great! You have decided to use a GAF shingle. Probably, you might have contacted a GAF certified roofing contractor near you for the big project. But beyond selecting the right GAF shingle and hiring a professional roofer near you for the job, how much do you know about GAF warranty? Is a GAF warranty necessary?

What Do The GAF Warranty Covers?

Aside from being every roofers’ and homeowner’s go-to choice of roofing material, thanks to their durability and aesthetically pleasing qualities, GAF roofing systems offer one of the best roofing warranties you can get out there.

GAF Limited Lifetime Warranty

A limited lifetime coverage means that the guarantee will remain valid for a long period. It remains valid as long as the original homeowner of the home where the GAF shingles were installed is still the owner. However, thanks to the Smart Choice® Protection Period, the original owner can now transfer this warranty to a second owner.

All GAF Roofing systems, by default, qualifies for the GAF Limited Warranty. This GAF remarkable warranty mostly applies to shingles and other materials installed on single-family houses—typically owned by individuals. Where other types of buildings like commercial buildings are involved, the warranty will only be for 40 years.

Types Of GAF Warranty

Typically, a manufacturer warranty offers protection from manufacturing defects, while a contractor warranty covers workmanship errors during the installation process. Although these two are separate warranties, GAF takes the game a level higher by bringing these two together.

There are different types or levels of GAF Shingle & Accessory Limited warranties. Understanding these warranties will give you a better idea of what GAF warranties cover.

GAF System Plus Limited Warranty

When your roofing system comes with GAF shingles and not less than three products, which are all equally installed by a GAF Master Elite® roofing contractor, then your roof will be automatically eligible for this type of warranty.

This warranty covers roof tear-off, provides wind warranty term of up to 15 years, provides an algae warranty of up to 25 years, and comes with a 50-year Smart Choice® Protection Period.

Silver Pledge™ Limited Warranty

The Silver Pledge™ Limited Warranty is just like the System Plus Limited Warranty. However, it adds a 10-year workmanship coverage.

Golden Pledge® Limited Warranty

This type of warranty covers everything found in the other two warranty levels, but instead of the ten-year workman warranty, it extends it to up to 30 years.

How To Register Your GAF Warranty

Beyond the question of how to register your GAF warranty, you should ask yourself, do you need to register for the warranty?

The simple answer is no.

Generally, you don’t need to register for any of the basic GAF shingle & Accessory Limited Warranty. All you have to do is always keep your purchase invoice close by.

However, you’ll be duly informed about other forms of GAF warranties that require registration by your GAF certified installer. This installer will also register them for you.

If you want a roofing system that will give you absolute peace of mind? Try the GAF system.

Looking for a certified and professional GAF roofer in Long Island, contact us at GAF Roofing Long Island 70 Sunrise Highway #500 Valley Stream, New York 11581 (516) 252-3001 https://www.gafroofinglongisland.com/.


Bushwick Roofing Is The Premier Roofing Contractors In The New York City Area. Enjoy Certified, Insured, Licensed & Bonded Contracting Service Today By Calling Us Now Or Filling Out Our Contact Form
Contact Us

70 Sunrise Highway #500 Valley Stream, New York 11581

Drag a button, link, or anything else into the icon box to place it below the text. Lorem ipsum dolor sit amet elit.

[email protected]

Drag a button, link, or anything else into the icon box to place it below the text. Lorem ipsum dolor sit amet elit.

Copyright Ⓒ 2020 Royal Renovators Inc. All Rights Reserved